Inspection

Inspection Details

Equipment ID
17397

Inspection Date
10/10/2023

Inspection Type
Alteration

Inspector Name
Curtis Belew

Mechanic Name
Bill Suedkamp

Relief Valve Pressure
340

Slide
NA

Governor Rope Pull
NA

Door Closing Force
NA

External ID
2aaecd67-aa5c-4ad6-87c1-62855b396adb

Location

St. Charles Center II
820 S Main St, St. Charles, MO
Phone: (314) 441-2602

Owner

Attn: Mark Milburn
St. Charles Center II
820 S Main St, St. Charles, MO 63301
Phone: (314) 441-2602
Email: markmilbrn@aol.com

Billing

Attn: Mark Milburn
Reco Development
P.O. Box 190, O'Fallon, MO 63366
Phone: (314) 441-2602
Email: markmilbrn@aol.com

Violations

Code	Item	Section	Reinspection	Reason For Violation	Fixed Date
conversion	conversion	n/a		Post current State certificate in machine room	4/17/2019
conversion	conversion	n/a		Provide self closing & locking machine room door	4/17/2019
conversion	conversion	n/a		Remove all non elevator storage from machine room	4/17/2019
MO Minimum : Elevators	(G) - Maintenance, Repair and Replacements	8.6.1.2.1 General Maintenance Requirements Documentation		Need testing procedures in the MCP on or by 1/1/2022	4/4/2022
MO Minimum : Elevators	CSR 40-5.100 State Operating Certificate	5.100(2) Display of Operating Certificate		Post current state certificate in machine room	9/11/2023
MO Minimum : Elevators	(H) - Machine Rooms	(H)2	x	The machine room shall have a self-closing and self-locking door and shall be operable from the interior space without use of a key. Note: The machine room door isn't self-closing and is incapable of being locked.	6/12/2024
MO Minimum : Elevators	(G) - Maintenance, Repair and Replacements	8.6.1.6.7 Signs and Data Plates	x	Each spring buffer shall be provided with a marking plate showing it's load rating, stroke, and the number of springs. Where the springs are removable, each spring shall be identified, and the assembly marking plate shall indicate this identification. Markings shall be made in a permanent and legible manner.	6/12/2024
A17.1-2016 : Elevators	2.14 - Code data plate	8.9	x	An individual data plate shall be provided and maintained for each unit. The data plate shall indicate the code to be used for inspections and test. The data plate shall indicate the code and edition in effect at the time of installation. The data plate shall also indicate the code in effect at the time of any alteration and indicate the applicable requirements of section 8.7. The data plate shall be in plain view, securely attached to each main line disconnect or controller. The data plate shall be of such material and construction that the letters and figures stamped, etched, cast, or otherwise applied to the face shall remain permanently and readily legible. The height of the letters and figures shall be not less than 0.125"	6/12/2024
MO Minimum : Elevators	(H) - Machine Rooms	(H)2		Machine room door to be self closing and self locking	8/1/2024
MO Minimum : Elevators	(G) - Maintenance, Repair and Replacements	(G)1 Maintenance, Repair and Replacements		Repair light on top of car	8/1/2024
MO Minimum : Elevators	CSR 40-5.100 State Operating Certificate	5.100(2) Display of Operating Certificate		Post current state certificate in machine room	8/1/2024
MO Minimum : Elevators	CSR 40-5.100 State Operating Certificate	5.100(2) Display of Operating Certificate		A current MO State operating certificate shall be posted in the machine room, in a noncombustible frame with a clear protective vision plate over it.	5/12/2025
MO Minimum : Elevators	(G) - Maintenance, Repair and Replacements	8.6.1.2.2 On-Site Documentation		A current maintenance control program (MCP) shall be provided in the machine room.	5/12/2025

Back