|
MO Minimum : Elevators
|
CSR 40-5.100 State Operating Certificate
|
5.100(2) Display of Operating Certificate
|
|
|
A current MO State operating certificate shall be posted in the elevator equipment room, in a noncombustible frame with a clear protective vision plate over it.
|
6/23/2022
|
|
MO Minimum : Elevators
|
(A) - Hoistways
|
(A)10
|
|
|
Access means shall be provided at one (1) upper landing to permit access to the top of the car, and at the lowest landing if this landing is the normal point of access to the pit
|
|
|
MO Minimum : Elevators
|
(A) - Hoistways
|
(A)10
|
|
|
Access means shall be provided at one (1) upper landing to permit access to the top of the car, and at the lowest landing if this landing is the normal point of access to the pit.
|
|
|
MO Minimum : Elevators
|
(H) - Machine Rooms
|
(H)1
|
|
|
Access to the machine room shall be safe. The brickwork above the machine room door and on the stairway landing is falling down, and shall be repaired.
|
6/23/2022
|
|
MO Minimum : Elevators
|
(A) - Hoistways
|
(A)5
|
|
|
All hoistway doors shall have pull straps.
|
12/7/2020
|
|
MO Minimum : Elevators
|
(G) - Maintenance, Repair and Replacements
|
8.6.1.4 Maintenance records
|
|
|
All the on site documentation required by A17.1 2016 - 8.6.1.2.2 and 8.6.1.4 shall be provided in the machine room.
|
6/23/2022
|
|
MO Minimum : Elevators
|
(C) - Car Enclosure: Freight
|
(C)6
|
|
|
Each freight car enclosure shall have a "No Passengers" sign conspicuously posted.
|
12/7/2020
|
|
MO Minimum : Elevators
|
(H) - Machine Rooms
|
(H)4
|
|
|
Equipment in the machine room not being used in conjunction with the function or use of the elevator shall be removed.
|
6/23/2022
|
|
MO Minimum : Elevators
|
(A) - Hoistways
|
(A)10
|
|
|
Hoistway access means shall be provided at the top and bottom floor.
|
12/7/2020
|
|
MO Minimum : Elevators
|
(H) - Machine Rooms
|
(H)6
|
|
|
Machines, motors, and disconnects shall be conspicuously marked.
|
6/23/2022
|
|
MO Minimum : Elevators
|
(A) - Hoistways
|
(A)5
|
|
|
Pull straps shall be installed on all hoistway doors.
|
6/23/2022
|
|
MO Minimum : Elevators
|
(C) - Car Enclosure: Freight
|
(C)2
|
|
|
Repair holes in car gate. Gates shall be constructed as to reject a ball two inches (2") in diameter. They shall withstand a force of two hundred fifty (250) pounds pressure applied in the center of the gate without breaking or forcing it out of its guides.
|
|
|
MO Minimum : Elevators
|
(G) - Maintenance, Repair and Replacements
|
8.6.3.1 Replacement Parts
|
|
|
Replace missing covers on exposed wiring on the car top and SOS switch.
|
|
|
MO Minimum : Elevators
|
(L) - Wire Ropes-Hoisting, Governor and Tiller
|
(L)12 (Re- Inspection)
|
x
|
|
Replace the governor rope.
|
2/26/2020
|
|
MO Minimum : Elevators
|
(G) - Maintenance, Repair and Replacements
|
8.6.3.1 Replacement Parts
|
|
|
The bolt holding the compensation chains is bent. The bolt needs to be straightened and possibly replaced
|
|
|
MO Minimum : Elevators
|
11 CSR 40-5.090 Inspection and Testing
|
(1) Minimum Standard
|
x
|
|
The car leveling device shall operate properly.
|
9/28/2020
|
|
MO Minimum : Elevators
|
(I) - Pits
|
(I)8
|
|
|
The drain hole in the pit floor shall be covered flush with the floor.
|
6/23/2022
|
|
MO Minimum : Elevators
|
(H) - Machine Rooms
|
(H)8
|
|
|
The mainline disconnect duct shall have a cover installed.
|
12/7/2020
|
|
MO Minimum : Elevators
|
11 CSR 40-5.090 Inspection and Testing
|
(1) Minimum Standard
|
x
|
|
The movement of the safety drum rope, starting from a fully retracted position, must not exceed 36". (It pulled out 60")
|
3/1/2022
|
|
MO Minimum : Elevators
|
(H) - Machine Rooms
|
(H)2
|
|
|
The radiator in the machine room shall be properly fastened or removed.
|
12/7/2020
|
|
MO Minimum : Elevators
|
(H) - Machine Rooms
|
(H)4
|
|
|
The water on the machine room floor shall be removed, and the leak repaired.
|
6/23/2022
|
|
MO Minimum : Elevators
|
(C) - Car Enclosure: Freight
|
(C)4
|
|
|
top. The top may be solid or open-work construction and shall be of metal. The open work shall reject a ball two inches (2") in diameter. Car tops shall be constructed to sustain a load of two hun- dred (200) pounds applied at any point on the car top. The top shall not have hinged or folding panels other than the emergency exit cover.
|
|